More EMC Applications

The EMC Shop will begin developing unique areas for EMC test applications including automotive, smart grid and medical testing. If you are looking for something specific and do not see it listed please contact us and we will do our best to point you in the right direction.

More EMC Applications There are 10 products.

Showing 1 - 10 of 10 items
    • Test procedure acc. IEC 61000-4-6 Ed. 4
    • Built-in amplifier saturation and linearity check
    • Built-in power amplifier 25 to 80 watts, 10 kHz to 400 MHz
    • Built-in power meter, 9 kHz to 1 GHz
    • Built-in dual directional coupler
    • Automatic calibration via built-in power meter
    • Connection for external amplifiers up to 1 GHz
    • USB-Interface
    • Software for Windows 7, Windows 8
    Typically In Stock
    Request Quote/More Info
    • Built-in EFT/Burst generator module
    • Built-in Micropulse generator module (ISO 7637, JASO, SAE and NISSAN)
    • Built-in coupling/decoupling network, 80V/50A, 100A@500ms
    • Built-in battery switch
    • Overcurrent protection
    • USB and GPIB-Bus
    • Emergency stop
    • Software for Windows Vista & Windows 7
    Typically In Stock
    Request Quote/More Info
    • Voltage up to 60V
    • Current up to 10A (peak up to 15 A)
    • Bipolar-amplifier models available
    • Low output impedance
    • Powerful DC voltage source
    • Pulses 4 and 2b (ISO 7637-2/ISO 16750-2)
    • Pre-programmed test routines to simulate various supply waveforms
    • Input for external signal generator to produce most complex waveforms
    • Software for Windows Vista & Windows 7
    • USB and GPIB interfaces
    In Stock
    Request Quote/More Info
    • Economic Alternative for Automotive EMC Compliance
    • Meets ISO 7637 Pulses 1, 2a, 3a aand 3b
    • Built-in EFT/Burst generator module
    • Built-in Micropulse generator module (ISO 7637, JASO, SAE and NISSAN)
    Typically In Stock
    Request Quote/More Info
    • Frequency Range: 10 KHz - 300 MHz
    • Transfer Impedance: -25 to 1 dBW
    • Current:  350 Amps Max
    • Individually Calibrated
    • FCC, MIL-STD, VDE and TEMPEST Testing
    • Rugged Construction
    Typically In Stock
    Request Quote/More Info
    • 9kHz to 1GHz Signal Generator 
    • Amplitude modulation: 1Hz to 3kHz (0% to 95%)
    • Pulse modulation: 1Hz - 1kHz (10% to 90%)
    • Built-in amplifier, 100kHz to 300MHz 
    • Built-in current monitor, 9kHz to 1GHz  
    Typically In Stock
    Request Quote/More Info
    • motorized wooden turntables
    • low profile
    • testing platforms for rotating equipment under test (EUT)
    • remote switch
    Typically In Stock
    Request Quote/More Info
    • Economic Alternative for Automotive EMC Compliance
    • Meets ISO 7637 Pulses 1, 2a, 3a and 3b
    • Built-in EFT/Burst generator module
    • Built-in Micropulse generator module (ISO 7637, JASO, SAE and NISSAN)
    $1,875.00
    Typically In Stock
    Request Quote/More Info
    • Load Dump generator according to ISO 7637, ISO 16750-2, SAE J1113, SAE J1455, JASO, Nissan and most car manufacturer requirements 
    • Generates Clipped Load Dump pulses 
    • Built-in 0.5 - 38 Ohm source impedance, selectable in 0.1 Ohm steps 
    • Pulse duration up to 1,200ms
    Inquire for Qty In Stock
    Request Quote/More Info
    • 9kHz to 1GHz Signal Generator 
    • Amplitude modulation: 1Hz to 3kHz (0% to 95%)
    • Pulse modulation: 1Hz - 1kHz (10% to 90%)
    • Built-in amplifier, 100kHz to 300MHz 
    • Built-in current monitor, 9kHz to 1GHz  
    $1,950.00
    Typically In Stock
    Request Quote/More Info
Showing 1 - 10 of 10 items