Quick Links

Information

EN/IEC 62132

EN/IEC 62132 RF Immunity Test Methods:

  • Radiated Immunity—TEM cell method. IEC 62132-2 defines a method of measuring an IC's immunity to radiated emissions. To test an IC using this method, you mount the DUT on the test board and install it in a mating port cut in the top or bottom of a TEM cell or GTEM cell. You must test the DUT in at least two...

EN/IEC 62132 RF Immunity Test Methods:

  • Radiated Immunity—TEM cell method. IEC 62132-2 defines a method of measuring an IC's immunity to radiated emissions. To test an IC using this method, you mount the DUT on the test board and install it in a mating port cut in the top or bottom of a TEM cell or GTEM cell. You must test the DUT in at least two orientations to ensure complete exposure to the generated electric field.
  • Conducted Immunity—Bulk Current Injection (BCI) method. IEC 62132-3 defines a method of evaluating immunity of the DUT to electromagnetic fields coupled to cables or cable bundles connected to the package pins. You can use this method to evaluate the immunity of IC pins connected to cables and also to evaluate other pins as well. The test signal is inductively coupled to the pin or pins under test using a current probe. Since you must connect the pins of the DUT to a cable or wire to inject the test signal, you can use a DUT application board or an IC EMC test board to perform this test.
  • Conducted Immunity—Direct RF Power Injection (DPI) method. IEC 62132-4 also defines a method of evaluating immunity of the DUT to electromagnetic fields coupled to cables or cable bundles connected to the package pins. When using this method, however, you directly inject the test signal using capacitive coupling to inject the signal on the cable or wire. The DUT can be mounted on either an IC EMC test board or an application board.
  • Conducted Immunity—Workbench Faraday Cage (WBFC) method. IEC 62132-5 defines a method for evaluating the immunity of an IC to signals injected at defined common-mode points. The DUT can be mounted on either an IC EMC test board or an application board, provided the board fits in the cage. With all input, output, and power connections to the test board filtered and connected to common-mode chokes, you must inject the conducted noise at PCB locations specified by the standard.
  • DPI (Direct Power Injection) (62132-4) widely used technique, especially in automotive applications.

The DPI test method is popular sice the DPI testing is very simple and straightforward to perform, and DPI testing can be easily simulated by chip designers using their standard design tools.

Turn Key Solution

Turnkey IEC 62132 Solution for DPI, BCI and other Test Methods.

The EMC Shop will provide complete turn-key solutions for compliance testing in accordance with EN/IEC 62132-X standards about 150 kHz to 1 GHz frequency range.

Get Application Support, Pricing, Lead Time and More: Contact Form

More

EN/IEC 62132 There are 17 products.

per page
Showing 1 - 12 of 17 items
    • Max EUT Size: 200 x 200 x 150 mm (7.87 x 7.87 x 5.9)in.
    • Max EUT dimension for uniform-area: (83 x 83 x 83 mm) (3.26 x 3.26 x 3.26in.)
    • Test cell with special opening to test integrated circuits on approx. 45 mm septum height
    • Meets IEC/EN 61000-4-20, SAE J1752/3, IEC 62132-2 and IEC 61967-2
    • For 100 Watts input power
    • Excellent VSWR up to 18 GHz
    Request Quote/More Info
  • Request Quote/More Info
    • Integrated signal generator 9 kHz to 1 GHz
    • 3 power meter inputs 9 kHz to 1 GHz
    • Integrated power amplifier module for different applications
    • Multiple EUT monitoring options
    • Optional built-in amplifier up to 75 watts (150 kHz - 230 MHz)
    • Meet IEC 61000-4-6,  IEC 61000-4-3, IEC 61000-4-20, IEC 61000-4-21 
    • Meet Mil-STD 461 CS114
    Request Quote/More Info
    • 9kHz to 1GHz Signal Generator 
    • Amplitude modulation: 1Hz to 3kHz (0% to 95%)
    • Pulse modulation: 1Hz - 1kHz (10% to 90%)
    • Built-in amplifier, 100kHz to 300MHz 
    • Built-in current monitor, 9kHz to 1GHz  
    Request Quote/More Info
    • Used unit comes with 6 month warranty
    • NIST Calibration Certificate
    • Digital sweep in discrete steps
    • 9 kHz to 6 GHz
    • Frequency, level and LF sweeps
    • AM, broadband FM/phase (optional), pulse modulation
    • Includes Rear Connectors R&S® SMA-B81
    • Built-in LF generator up to 1 MHz
    • Very low SSB phase noise
    • Very short frequency and level setting times
    • Fast hopping mode
    Request Quote/More Info
    • Signal generator 5 kHz to 6 GHz
    • Multifunction Generator:
      • produces stereo multiplex and VOR/ILS signals
      • sinewave
      • noise 0.1 Hz to 1 MHz
      • triangular
      • sawtooth
      • squarewave 0.1 Hz to 50 kHz signals
    $5,900.00
    Request Quote/More Info
    • 9 kHz to 2.4 GHz Frequency Range
    • Linear and Logarithmic Sweep Mode
    • RS232 & GPIB Control
    • Small footprint for bench or rack use
    • Reverse Power Protected to 50 W
    • 1 Hz Resolution
    • -140 to +13 dBm Peak RF output level with 0.1 dB Resolution
    • AM, FM, Amplitude, Phase, Pulse, FSK Modulation
    • 3.9 kHz Bessel filtered FSK
    • Sine, Triangular and Square Two-Tone Modulation Source
    $2,000.00
    Request Quote/More Info
    • Integrated signal generator 4 kHz to 1 GHz
    • 3 power meter inputs 4 kHz to 1 GHz
    • Integrated class A power amplifier module:
      Multiple EUT monitoring options
      • 45 W, 9 kHz to 1 GHz
    • 5,7“ TFT color display
    • Internal, menu-based control software
    • Basic remote control software and report generator included
    • Optically decoupled remote control
    • Whisper mode
    Request Quote/More Info
    • 150 kHz to 230 MHz Power amplifier frequency range
    • 4 kHz to 1 GHz Integrated signal generator
    • 4 kHz to 1 GHz 3 power meter inputs
    • Integrated class A power amplifier module for different applications:
      • 35 W, 150 kHz to 230 MHz;
      • 40 W, 10 kHz to 400 MHz;
      • 45 W, 9 kHz to 1 GHz;
      • 60 W, 10 kHz to 400 MHz;
      • (>10 W, 4 kHz to 10 kHz); 80 W, 150 kHz to 230 MHz
    • Multiple EUT monitoring options
    • 5,7“ TFT color display
    • Internal, menu-based control software
    • Basic remote control software and report generator included
    • Optically decoupled remote control
    • Whisper mode
    Request Quote/More Info
    • 150 kHz - 230 MHz Frequency Range
    • Turnkey software for IEC 61000-4-6
    • 25 Watt Integrated Amplifier
    • Computer Based System (USB controlled)
    • Self Calibration with CDN, EM Clamp or Injection Probe
    • RF generator, amplifier and RF Voltmeter usable as independent instruments
    • Connections: EUT "Fail", EUT monitoring by external multimeter
    Reduced price!
    Request Quote/More Info
    • Integrated signal generator 4 kHz to 1 GHz
    • 3 power meter inputs 4 kHz to 1 GHz
    • Integrated class A power amplifier module:
      Multiple EUT monitoring options
      • 80 W, 150 kHz to 230 MHz
    • 5,7“ TFT color display
    • Internal, menu-based control software
    • Basic remote control software and report generator included
    • Optically decoupled remote control
    • Whisper mode
    Request Quote/More Info
    • 9kHz to 1GHz Signal Generator 
    • Amplitude modulation: 1Hz to 3kHz (0% to 95%)
    • Pulse modulation: 1Hz - 1kHz (10% to 90%)
    • Built-in amplifier, 100kHz to 300MHz 
    • Built-in current monitor, 9kHz to 1GHz  
    $1,950.00
    Request Quote/More Info
Showing 1 - 12 of 17 items