> Application/Test Type>CE Mark Testing>Radiated Emissions
Radiated Emissions

Radiated emissions measurements are required for CISPR 11, 14, 22, Mil-STD 461 RE 101/02/03 and many other compliance standards. The EMC Shop supplies turn key solutions for precompliance evaluation or stand alone equipment such as antennas, measurement receivers/spectrum analyzers and LISN's. Submit a quote request from any product page to request more information on available radiated emissions test equipment.

Radiated Emissions There are 29 products.

Subcategories

  • Radiated Emissions Turnkey Bundles

    Rent, buy or lease turnkey test equipment bundles for radiated emissions testing to FCC, MIL-STD and more. The EMC Shop specializes in emissions test, pre-certification and compliance.

  • EM Absorbing Clamps

    The EMC Shop specializes in measuring power disturbances in accordance to CISPR and EN compliance test standards. Rent, buy or lease EM Absorbing Clamps. 

    EM Absorbing Clamps

    CISPR 14 (EN 55014)

    CISPR 16-1-4

    CISPR 16-2-3

    CISPR 11

    CISPR 16-2-2/EN 55016-2-2

    CISPR 13/EN 55013

    CISPR 14-1/EN 55014-1

    EN 50083-2

  • Accessories

    Accessories

per page
Showing 1 - 12 of 29 items
  • Quick view
    • FPC1000 Low-Cost Spectrum Analyzer for Emissions Testing
      • Frequency range: 5 kHz to 1 GHz, Upgradable to 2 GHz or 3 GHz
      • Resolution bandwidth settings down to 1 Hz
      • 10.1" WXGA (1366 x 768 pixel) display
      • Wi-Fi-enabled w/ remote control (included)
      • Easy virtual control w/ iOS/Android/PC
      • Low noise floor / High max. input power
      • Receiver mode for EMI debugging on circuit boards, integrated circuits, cable shielding, etc.
    • HM6050-2 Line Impedance Simulation Network
      • Frequency range from 9 kHz to 30 MHz
      • Built-in transient limiter
      • Artificial hand connector
    • HZ540 Near Field Probes
      • Frequency range from 100 kHz to 1/3 GHz
      • Probes included (1 × Electrical Field Probe, 1 × Magnetic Field Probe, 1 × High Impedance Probe)
    • EMC PreCom
      • EMC Precompliance Software (EMC PreCom) -- EMI module part of the HMExplorer software for conducting precompliance measurements (only with HO720 USB/RS-232 or the optional HO732 Ethernet/USB interface)
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    • 20 Hz to 2 GHz
    • Individually Calibrated
    • Log Periodic Antenna
    • Biconical Antenna and more
    • FCC, MIL-STD, VDE and TEMPEST Testing
    • Rugged Construction
    • Three Year Warranty
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    • FPC1000 Low-Cost Spectrum Analyzer for Emissions Testing
      • Frequency range: 5 kHz to 1 GHz, Upgradable to 2 GHz or 3 GHz
      • Resolution bandwidth settings down to 1 Hz
      • 10.1" WXGA (1366 x 768 pixel) display
      • Wi-Fi-enabled w/ remote control (included)
      • Easy virtual control w/ iOS/Android/PC
      • Low noise floor / High max. input power
      • Receiver mode for EMI debugging on circuit boards, integrated circuits, cable shielding, etc.
    • USMC0125 Low Noise Preamplifier
      • 30 - 33 dB Gain, Max 2:1 VSWR
      • Frequency Range from 1 MHz - 2.5 GHz
      • Built in battery or external DC supply
      • IP65 / IP60 compliant and conforms to European RoHS and ECCN EAR99
    • SAS-542 Biconical Antenna
      • Ideal for compliance emission testing
      • Conventional VHF broadband test antenna
    • SAS-510-2 Log Periodic Antenna
      • 290 MHz - 2000 MHz
      • 1000 Watts Maximum Continuous Power
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    $1,775.00
    • Test Systems in stock, available to ship today
    • Basic RF emissions monitoring with GTEM as isolation
    • Inquire to order compliant CISPR EMI receivers
    • GTEM for DUT up to 8" x 8" x 6" (Inquire for larger GTEMs)
    • All Test Equipment to generate and monitor testing to IEC 61000-4-3
    $1,775.00
    Add to cart
    Request Quote/More Info
    Add to Compare
  • Quick view
    • FPC1000 Low-Cost Spectrum Analyzer for Emissions Testing
      • Frequency range: 5 kHz to 1 GHz, Upgradable to 2 GHz or 3 GHz
      • Resolution bandwidth settings down to 1 Hz
      • 10.1" WXGA (1366 x 768 pixel) display
      • Wi-Fi-enabled w/ remote control (included)
      • Easy virtual control w/ iOS/Android/PC
      • Low noise floor / High max. input power
      • Receiver mode for EMI debugging on circuit boards, integrated circuits, cable shielding, etc.
    • Teseq ISN T8 Impedance Stabilization Network (ISN) for Unscreened Balanced Pairs
      • For use with one, two, three, or four unscreened balanced pairs
      • Refers schematic circuit example in CISPR 22/32 Figure D.3/G.3
      • Intended for connection to cable category 3 and 5
      • 1000BaseT and PoE application
      • Changeable pin-arrangements with RJ11 and RJ45
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Rent the Keysight (Agilent) N9038A-526-B85-RT1
    • 3 dB resolution bandwidths
    • Quasi-peak, EMI-avg, RMS-avg and diagnostic detectors
    • Meets CISPR 16-1-1: 2010 and MIL-STD-461F EMI receiver requirements
    • ±0.5 dB absolute amplitude accuracy
    • -166 dBm displayed average noise level (DANL) with preamplifier and noise floor extension
    • EMC measurements offering simultaneous detectors, signal lists, scan tables, limit lines, and correction factors
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    $1,475.00
    • Rugged Maple wood construction
    • Standard 1/4-20 mounting thread
    • Reversible legs: Rubber feet for lab use, spike tips for outdoor testing
    • lightweight and durable wooden legs
    • Rugged Construction
    • Folded Height: 25" (64 cm)
    • Max Height: 62" (158 cm)
    • Weight: 10.2 lbs (4.6 Kg)
    $1,475.00
    Add to cart
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Frequency range: 5 kHz to 1 GHz, Upgradable to 2 GHz or 3 GHz
    • Resolution bandwidth settings down to 1 Hz
    • 10.1" WXGA (1366 x 768 pixel) display
    • Wi-Fi-enabled w/ remote control (included)
    • Easy virtual control w/ iOS/Android/PC
    • Low noise floor / High max. input power
    • Receiver mode for EMI debugging on circuit boards, integrated circuits, cable shielding, etc.
    • Three-year warranty
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Easily adjust and redirect EMC antenna
    • Leveling bubble
    • Metal construction
    • Standard 1/4-20 mounting threads
    • 4" mounting surface
    • Weight: 0.7 lbs (317g)
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Rugged Maple wood construction
    • Standard 1/4-20 mounting thread
    • Reversible legs: Rubber feet for lab use, spike tips for outdoor testing
    • lightweight and durable wooden legs
    • Rugged Construction
    • Folded Height: 40" (101 cm)
    • Max Height: 64" (163 cm)
    • Weight: 11.3 lbs (5.1 Kg)
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Easily adjust and redirect EMC antenna
    • Leveling bubble
    • Nylon construction
    • Standard 1/4-20 mounting threads
    • 4" mounting surface
    • Weight: 0.7 lbs (317g)
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    $950.00
    • Rental Rate Per Month - 3 Month Minimum Required
    • Rentals ship immediately
    • 9 kHz - 3 GHz
    • Automatic EMI measurements
    • High accuray and response
    • Compatible with the BenchLink Web Remote software
    • Log sweep
    • 5 minute warm-up
    • Built-in preamplifier
    $950.00
    Add to cart
    Request Quote/More Info
    Add to Compare
Showing 1 - 12 of 29 items