Electrostatic Discharge Immunity Test

(Showing 12 of 24)

Most engineers have fundamental EMC understanding, including the experience of witnessing the ESD testing in a test lab. The test lab often relies on the product manufacturer to determine the test points as they draft the test plan in accordance to the product compliance standard, IEC/EN 61000-4-2 is a common electrostatic discharge immunity test standard, often referred to in product standards.

Most elecrostatic discharge testing, to most standards, will instruct the technician to run a test sequence of ten discharges in one second intervals in both positive and negative polarity. The test standard may notate a ‘test environment’ consisting of a test bench and grounding plane. For pre compliance testing, this may not be necessary. But take care to not discharge near other (expensive) electronics in use. With each electrostatic discharge, an EM pulse is emitted from the simulator and can affect nearby equipment. For precompliance, ESD generators have a voltage potentiometer to identify failure thresholds.

What is an Electrostatic Discharge Immunity Test

The primary goal is to replicate electric static and apply the event to a selected amount of test points. Common locations on todays commercial electronics include a USB port and the touch screen interface. Other locations on the chassis where a user may grab the product should be tested.

Electrostatic Discharge Immunity Test Setup

The goal is to directly apply the electrostatic discharge to the product under test using the contact tip. However, in most instances where a test point is to a non-conductive surface, the air tip is used. The user pulling the trigger to charge the air tip and approach until the discharge. There may be instances where an ESD event is not observed, assuming your electrostatic generator is functioning properly, this is OK and your product passes.

Electrostatic Discharge Immunity Test Test Equipment, Systems & Solutions

Quick view

3ctest EDS 30S Electrostatic Simulator for Initiating Explosive Devices

Features: 5.7" Touch Screen Interface, Explosives box and R/C Switch

Test Standards: Mil-STD 331, MIL-STD 464, MIL-DTL-23659, GJB 736.11:1990, MIL-STD-1751A, (Group 1030 Test Methods) along with MIL-STDs 1512, 1576 (Method 2205) and MIL-STD-331B (Notice 3)

Applications: Military EMC testing

CALL FOR LEAD TIME

View Product Cart
Quick view

3ctest EDS 30V Automotive ESD Simulator for ISO 10605

SKU: sku-1087

Test Standards: ISO 10605 ed 3, IEC 61000-4-2, ISO 60601-1-2, MIL-STD-461 CS118, RTCA/DO-160

ESD Voltage Output Range (Air/Contact): 30kV

Interchangeable R/C Modules: Yes

Battery Life: 8 Hours

Applications: EV and Automotive

Voltage Resolution: 100 Volts

Videos: Interface Overview, Setting up an ESD Test Environment

IN STOCK

View Product Cart
Quick view

3ctest EDS 16H Electrostatic Discharge Simulator up to 16 kV, IEC/EN 61000-4-2 Compliance

SKU: sku-712

Weight: Approx 7kg

Air Discharge Voltage Range: 1000V – 16,000V （±5%）

Battery: at least 16 hour battery life

Contact Discharge Voltage Range: 1000V – 16,000V （±5%）

Frequency Capabilities: single/0.1/0.2/0.5/1/2/5/10/20 Hz

Holding Time: More than 5 sec

Polarity: positive & negative

Pre-Programmed IEC Levels: Yes

Resolution: 100V steps

Standards Met: IEC/EN 61000-4-2, ISO 10605

Typically In Stock

View Product Cart
Quick view

GRC Series Ground Cable w/ 470k Ohm Resistors for ESD Voltage Bleeding

SKU: sku-680

MSRP:

Was:

$199.00

Price Now:

$198.99
Quick view

Haefely ONYX 16 ESD Simulator Gun for IEC 61000-4-2

SKU: 0536

Air Discharge Voltage Range: 1 to 16 kV or 1 to 30 kV

Battery: at least 16 hour battery life

Contact Discharge Voltage Range: 1 to 16 kV or 1 to 30 kV

Frequency Capabilities: single/0.1/0.2/0.5/1/2/5/10/20 Hz

Holding Time: More than 5 sec

Polarity: positive & negative

Pre-Programmed IEC Levels: Yes

Resolution: 100V steps

Standards Met: IEC/EN 61000-4-2, ISO 10605

MSRP:

Was:

Price Now:

$295.00

Ships Same Day

Ordering Options
Quick view

Haefely ONYX 30 ESD Simulator Gun

SKU: 10535

TEST IMMEDIATELY: ESD Gun Rentals Ship Same Day

Voltage Range: 1 to 30 kV

Standards Met: IEC/EN 61000-4-2, ISO 10605

Battery: at least 16 hour battery life

Frequency Capabilities: single/0.1/0.2/0.5/1/2/5/10/20 Hz

Holding Time: More than 5 sec

Pre-Programmed IEC Levels: Yes

Resolution: 100V steps

MSRP:

Was:

Price Now:

$495.00

In Stock

Ordering Options
Quick view

Thermo-Keytek MZ15/EC Minizap ESD Simulator for IEC 61000-4-2 - Used

SKU: 10322

Voltage Range: 500 Volts to 16 kV

EMC Standards: IEC 61000-4-2

IN A HURRY?: Rentals Ship Same Dy

MSRP:

Was:

Price Now:

$495.00

In Stock

Ordering Options
Quick view

Teseq NSG 435 Electrostatic Discharge Simulator

SKU: NSG-435-

Test Standards: IEC 61000-4-2

Applications: Medical, Commercial Electronics, IT, and more

Test Capabilities: Air/Contact up to 15kV

Pre-programmed Test Limits: Yes

More Resources: Test Setup, ESD Waveform, RMA Form

MSRP:

$10,150.00

Was:

Price Now:

$5,975.00

In Stock

Ordering Options
Quick view

Teseq INA 103 Calibration Adapter

SKU: sku-35

View Product Cart
Quick view

Teseq INA 4381 ISO 10605 Discharge Network

SKU: sku-22

MSRP:

Was:

Price Now:

$1,190.00
Quick view

Teseq NSG 438 30kV ESD Simulator Gun

SKU: 10121

Standards Met: IEC/EN 61000-4-2, ISO 10605

Need to test now?: ESD Gun Rentals Ship Same Day

Voltage Range: 200 V to 30k V (in 100 V steps)

Polarity: Positive / negative / automatic change

Pre-Programmed IEC Levels: Yes

Resolution: 100 V steps

MSRP:

Was:

Price Now:

$475.00

IN STOCK

Ordering Options
Quick view

Teseq NSG 437 ESD Simulator for IEC 61000-4-2 and ISO 10605

SKU: 10117

Test Standards: ISO 10605, IEC 61000-4-2, ISO 60601-1-2, MIL-STD-461 CS118, RTCA/DO-160

ESD Voltage Output Range (Air/Contact): 30kV

Interchangeable R/C Modules: Yes

Battery Life: None

Applications: EV and Automotive

Voltage Resolution: 100 Volts

NEED IT FAST?: ESD Gun Rentals Ship Same Day

MSRP:

Was:

Price Now:

$490.00

IN STOCK

Ordering Options