Ring Wave Immunity Generators

Quick Links

Information

Viewed products

Rent Haefely PIM 150 100 kHz & 1 MHz Oscillating Wave Surge Generator

Used

  • 75ns rise-time
  • 3.3kV impulse voltage
  • Source Impedance 200 Ohm
  • Integrated three phase CDN (Single Phase Avail)

More details

Typically In Stock

Request Quote/More Info

PDF Downloads

Specifications

Standards Met IEC 61000-4-12 Power & Data lines;  ANSI C37.90.1-2002 Power lines;  IEC 60255-22-1 Measuring relays and protection equipment; IEEE 1613 Substation Equipment
Mains & EUT Connections HV connector & CDN
Pulse voltage (open circuit) 480Vac (phase - phase) / 110Vdc
Pulse current (short circuit) 16A ac/dc per path
Coupling Single & Multiple Path
Polarity Positive, Negative & Alternating
Burst frequency 100kHz & 1MHz
Pulse repetition 40 Hz & 400Hz
Test Voltage 0.25 – 3.3kV
Rise time 75ns
Source Impedance 200 ohms
Burst duration 2 seconds to continuous

Test Equipment Description

Haefely PIM 150 Description:

IEC 61000-4-12 Ed.1, IEC IEC 61000-4-18 Ed.1 and ANSI C37.90 describe an oscillating wave generator with defined open circuit waveforms parameters. The oscillating wave, also called a “damped sine” is used to test the immunity of electronic relays and relay systems mounted in an electrical substation or similar harsh environment. IEC product standards such as IEC 60255-22-1 include this wave shape too.

Safety is paramount when AC and impulse voltages are being used. The PIM 150 High Voltage connections are all designed so no accidental contact can occur. In addition, the CDN input and output terminals use touch-proof connectors.

The Haefely PIM 150 contains an integrated Coupling/Decoupling Network (CDs) for superimposition of the impulse on AC and DC power lines. The integrated CDN is specially designed to ensure wave shape integrity at the test system output. PIM 150 maintains wave shape AND amplitude, even with multiple coupling paths selected.

PIM 150 with the PSURGE 8000 Surge Platform can perform all the programming functions required to perform IEC and ANSI testing without the need of a control computer. Voltage monitor circuits enable quick and easy verification of the impulse shape and amplitude. In addition, peak measurement circuits are used to help determine EUT PASS/FAIL criterion.

The integration in the WinFEAT&R control and reporting software package enhances an efficient set-up and operation of this test system. Most importantly, the test load can be transferred to a computer freeing valuable resources.

Benefits:

International application – Specifically designed to meet and exceed the requirements of IEC, EN, and ANSI tests for power line applications.

Accurate Impulses – The PIM 150 wave shape and amplitude are guaranteed to conform to specification at the CDN output. Also with simultaneous, multiple coupling path selections.

Safe and Easy – The interlocked HV section and the specially designed output sockets, allow your operators to test safely and easily.

Sturdy and Reliable – Careful component selection ensures that the PIM 150 will continue to operate under the most strenuous testing regime.

Report Generation – The unit can automatically generate test reports without a computer. Add WinFEAT&R control and reporting software to collect and collate data in any format you like.

Application:

  • Single & Three phase power line systems
  • IEC 61000-4-12 Ed.1 Power & Data lines
  • IEC 61000-4-18 Ed.1 D.O.W.
  • ANSI C37.90.1-2002 Power lines
  • IEC 60255-22-1 Measuring relays and protection equipment
  • IEEE 1613 Substation Equipment

Haefely PIM 150 Features:

  • 100kHz & 1MHz frequencies
  • 75ns rise-time
  • 3.3kV impulse voltage
  • Source Impedance 200 Ohm
  • Integrated three phase CDN
  • Variable burst duration
  • Single & Three phase power line systems
  • IEC 61000-4-12 Power & Data lines
  • ANSI C37.90.1-2002 Power lines
  • IEC 60255-22-1 Measuring relays and protection equipment
  • IEEE 1613 Substation Equipment

Associated EMC Test Equipment

13 other products in the same category: