EM Test Automotive Test Systems

The automotive industry has very specific and permanently changing requirements for EMC testing with pulses and waveforms getting more and more complex. As the leading manufacturer of automotive test equipment and member of various national and international standard working groups EM TEST knows the present and the future demands of the car indu...

The automotive industry has very specific and permanently changing requirements for EMC testing with pulses and waveforms getting more and more complex. As the leading manufacturer of automotive test equipment and member of various national and international standard working groups EM TEST knows the present and the future demands of the car industry.

The EM Test automotive test equipment listed below are well designed to meet the EMC testing requirements of the automotive industry including ISO 7637, ISO 11452 as well as manufacturer specific standards. The EMC Shop stocks an assortment of EM Test automotive test systems to get you up and running fast.

More

EM Test Automotive Test Systems There are 17 products.

per page
Showing 1 - 12 of 17 items
    • LD 200N Load Dump generator for ISO 7637 Pulses 5A, 5B, 7
    • VDS 200N50 Voltage Drop Simulator for ISO 7637  Pulses 2B and 4
    • UCS 200N Auto Transient/EFT Simulator for ISO 7637 Pulses 1, 2, 3A/3B
    • Load Dump CLD Module enables the LD 200N to generate clipped load dump pulses
    Request Quote/More Info
  • $3,790.00
    Request Quote/More Info
    • ISO PULSE 6 (12V/24V)
    • GOST PULSE 1B (24V)
    • Standalone test generator 
    • Test Voltage up to 1,100V
    • Includes 30, 50, 100, 150 and 200ohm source impedance
    • Built-in electronic battery switch
    • Built-in CDN 60V/25A DC
    Request Quote/More Info
    • Built-in EFT/Burst generator module
    • Built-in Micropulse generator module (ISO 7637, JASO, SAE and NISSAN)
    • Built-in coupling/decoupling network, 80V/50A, 100A@500ms
    • Built-in battery switch
    • Overcurrent protection
    • USB and GPIB-Bus
    • Emergency stop
    • Software for Windows Vista & Windows 7
    Request Quote/More Info
    • Voltage up to 60V
    • Current up to 10A (peak up to 15 A)
    • Bipolar-amplifier models available
    • Low output impedance
    • Powerful DC voltage source
    • Pulses 4 and 2b (ISO 7637-2/ISO 16750-2)
    • Pre-programmed test routines to simulate various supply waveforms
    • Input for external signal generator to produce most complex waveforms
    • Software for Windows Vista & Windows 7
    • USB and GPIB interfaces
    Request Quote/More Info
    • One-box transformer and 0.5 ohm load assembly
    • Frequency response 10 Hz to 250 kHz
    • Secondary saturation 50 A per transformer
    • Audio power 2 x 200 W
    • Freely configurable on primary/secondary; serial, parallel, single
    • Turns ratio 2:1 step down
    • Built-in non-inductive load resistor 0.5 ohm, 250 W
    Request Quote/More Info
    • Built-in DDS to generate sinusoidal signals up to 250kHz
    • Built-in LF amplifier, 250W
    • Output voltage max. 140V p-p, 50V rms
    • Output current max. 5A rms
    • Programmable DC voltage offset
    • Controlled by AutoWave and autowave.control via Framebus
    • Integrated voltage measurement 10Hz - 250kHz (optional)
    • Integrated field strength measurement (optional)

    Request Quote/More Info
    • Voltage up to 60 V, 2 ranges
    • Expandable to 77 V
    • Current up to 100 A (300 A peak)
    • Four quadrant operation
    • Fast step response time
    • Low output impedance
    • High Bandwidth
    • Temperature-controlled air cooling
    • Pre-programmed test routines to simulate various supply waveforms
    • Input for external signal generator to produce most complex waveforms
    • Software for Windows Vista & Windows 7

    Request Quote/More Info
    • Dual-Processor-Technology, 500kS/s sample rate
    • 4-channel arbitrary generator
    • 2-channel transient recorder
    • Simultaneous recording/generation
    • Library of standard test routines
    • Pseudo-random function
    • 60GB built-in hard disk
    • Multiple interfaces
    • Software for Windows Vista & Windows 7
    Request Quote/More Info
    • Voltage up to 60V
    • Current up to 10A (peak up to 15 A)
    • Bipolar-amplifier models available
    • Low output impedance
    • Powerful DC voltage source
    • Pulses 4 and 2b (ISO 7637-2/ISO 16750-2)
    • Pre-programmed test routines to simulate various supply waveforms
    • Input for external signal generator to produce most complex waveforms
    • Software for Windows Vista & Windows 7
    • USB and GPIB interfaces
    Request Quote/More Info
    • Load Dump generator according to ISO 7637, ISO 16750-2, SAE J1113, SAE J1455, JASO, Nissan and most car manufacturer requirements 
    • Generates Clipped Load Dump pulses 
    • Built-in 0.5 - 38 Ohm source impedance, selectable in 0.1 Ohm steps 
    • Pulse duration up to 1,200ms
    Request Quote/More Info
    • Standalone test generator for voltage dips and interruptions
    • Rise/fall time <1us
    • Electronic short-circuit protection
    • Rated voltage 80V DC
    • Front panel operation
    • Standard Test routines
    • USB and GPIB interfaces
    Request Quote/More Info
Showing 1 - 12 of 17 items