> Application/Test Type>CE Mark Testing>Conducted Emissions
Conducted Emissions

Commercial and industrial conducted emissions are performed to verify potentical harmful leakage between 150kHz and 30 MHz. Aerospace and miltary standards extend the frequnecy requirements to 9 kHz and up to 400 MHz in some cases. For sophisticated designs a dedicated EMI/EMC analyzer or a high end spectrum analyzer to identify low noise issues. Standard low cost spectrum analyzers can be used for simple verficiation checks. 

Conducted Emissions There are 53 products.

Subcategories

  • Analyzers, Receivers and Scopes

    Most any signal or spectral analysis unit can be used to evaluate the quality of your electrical components and DUT's. Quasi peak detection and EMI filters are offered as options by many manufacturers. EMI Receviers and EMC analyzers have the required hardware and software to help identiry problem areas in both conducted and radiated applications, saving time on pre-certifciation and saving money but better identifing issues that may cause failure at the certification lab.

  • Impedance Stabilization Networks (Power and Data Lines)

    Impedance Stabilization Networks  also known as Artificial Mains Networks are the most common transducer to perform conducted emission testing. For testing electrical power lines a Line Impedance Stabilization Network (LISN) is required. To test data lines an Impedance StabilizatioN Network (ISN) is used.

  • Transient Limiters

    Used between the LISN and measuring device such as an EMI receiver or a spectrum analyzer to protect the unit from high voltage spikes. Most transient limiters are spec'd to meet commerical and military conducted emissions standards (9 kHz to 30 MHz)

  • Preamplifiers

    Used inbetween close field probes and the measuring device (Spectrum analyzer or EMI receiver) to maximize performance of the probes and help identify problem areas while taking real time measurements.

  • Probes and Clamps

    Close field probes, current probes, voltabe probes and abosrbing clamps are scondary components required in some commercial and military & aerospace conducted emissions standards.

  • Accessories

    Conducted Emissions Accessories

  • Turnkey Bundles

    Rent, buy or lease turnkey test equipment bundles for conducted emissions testing to FCC, MIL-STD and more. The EMC Shop specializes in emissions test, pre-certification and compliance.

per page
Showing 1 - 12 of 53 items
  • Quick view
    • FPC1000 Low-Cost Spectrum Analyzer for Emissions Testing
      • Frequency range: 5 kHz to 1 GHz, Upgradable to 2 GHz or 3 GHz
      • Resolution bandwidth settings down to 1 Hz
      • 10.1" WXGA (1366 x 768 pixel) display
      • Wi-Fi-enabled w/ remote control (included)
      • Easy virtual control w/ iOS/Android/PC
      • Low noise floor / High max. input power
      • Receiver mode for EMI debugging on circuit boards, integrated circuits, cable shielding, etc.
    • HM6050-2 Line Impedance Simulation Network
      • Frequency range from 9 kHz to 30 MHz
      • Built-in transient limiter
      • Artificial hand connector
    • HZ540 Near Field Probes
      • Frequency range from 100 kHz to 1/3 GHz
      • Probes included (1 × Electrical Field Probe, 1 × Magnetic Field Probe, 1 × High Impedance Probe)
    • EMC PreCom
      • EMC Precompliance Software (EMC PreCom) -- EMI module part of the HMExplorer software for conducting precompliance measurements (only with HO720 USB/RS-232 or the optional HO732 Ethernet/USB interface)
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    $3,900.00
    • For use with one, two, three, or four unscreened balanced pairs
    • Refers schematic circuit example in CISPR 22/32 Figure D.3/G.3
    • Intended for connection to cable category 3 and 5
    • 1000BaseT and PoE application
    • Changeable pin-arrangements with RJ11 and RJ45
    $3,900.00
    Add to cart
    Request Quote/More Info
    Add to Compare
  • Quick view
    $1,912.50 $2,250.00 -15%
    • Rentals Ship Same Day
    • Typ. configured w/ NEMA
    • Suitable for making FCC 15, VDE 0871, VDE 0875 and EN 55022 conformance measurements
    • Insulated Plug for Safer Power Connections
    • Earth Line Choke isolates EUT from RF ground while maintaining a safety ground
    • Calibrated to ANSI C63.4
    $1,912.50 $2,250.00 -15%
    Add to cart
    Reduced price!
    Request Quote/More Info
    Add to Compare
  • Quick view
    • FPC1000 Low-Cost Spectrum Analyzer for Emissions Testing
      • Frequency range: 5 kHz to 1 GHz, Upgradable to 2 GHz or 3 GHz
      • Resolution bandwidth settings down to 1 Hz
      • 10.1" WXGA (1366 x 768 pixel) display
      • Wi-Fi-enabled w/ remote control (included)
      • Easy virtual control w/ iOS/Android/PC
      • Low noise floor / High max. input power
      • Receiver mode for EMI debugging on circuit boards, integrated circuits, cable shielding, etc.
    • Teseq ISN T8 Impedance Stabilization Network (ISN) for Unscreened Balanced Pairs
      • For use with one, two, three, or four unscreened balanced pairs
      • Refers schematic circuit example in CISPR 22/32 Figure D.3/G.3
      • Intended for connection to cable category 3 and 5
      • 1000BaseT and PoE application
      • Changeable pin-arrangements with RJ11 and RJ45
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Frequency Range: 1 MHz - 1 GHz
    • Max Current: 200 Amps DC to 60 Hz, 20 Amps CW (50 Amps Pulse)
    • Transfer Impedance: 24 dBΩ
    • Aperture: 1.2" (32 mm)
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    $5,457.00 $6,420.00 -15%

    • Rent the Com-Power ISN T8 here.
    • Frequency Range: 150 kHz to 30 MHz
    • For Unshielded Telecomunication Lines 1 to 4 balanced pairs
    • Complies with CISPR 16-1-2, CISPR 22/32
    • Individual Calibration Included
    $5,457.00 $6,420.00 -15%
    Add to cart
    Reduced price!
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Rent the Keysight (Agilent) N9038A-526-B85-RT1
    • 3 dB resolution bandwidths
    • Quasi-peak, EMI-avg, RMS-avg and diagnostic detectors
    • Meets CISPR 16-1-1: 2010 and MIL-STD-461F EMI receiver requirements
    • ±0.5 dB absolute amplitude accuracy
    • -166 dBm displayed average noise level (DANL) with preamplifier and noise floor extension
    • EMC measurements offering simultaneous detectors, signal lists, scan tables, limit lines, and correction factors
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    • 9 kHz a 30 MHz frequency range
    • 100 A max output current
    • Large baseplate for optimal grounding
    • Local and remote control for PMM EMI receivers
    • Meets the requirements of several standards including CISPR 16-1-2, VDE 0876, FCC part 15
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    $295.00
    • 9 kHz to 30 MHz Frequency Range
    • Fully Compliant with CISPR 16-1-2/ANSI C63.4
    • Dual-Conductor Network with Universal
    • Power Receptacle to accept any EUT Plug
    • 20 Amps Current Handling Capability
    • Three-Year Warranty
    $295.00
    Add to cart
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Price is for a pair of LI-125A line impedance stabilization networks
    • Fully compliant to CISPR 16-1-2 / ANSI C63.4
    • "Air-core" inductors to prevent saturation
    • Provides a near 1:1 (<0.5 dB insertion loss) 50Ω coaxial measurement port (type-N)
    • Provides a defined, stable, impedance to the Equipment Under Test (EUT)
    • Individual Calibration Included
    • Three Year Warranty on New Units
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Price is for a pair of LI-125A line impedance stabilization networks
    • Fully compliant to CISPR 16-1-2 / ANSI C63.4
    • "Air-core" inductors to prevent saturation
    • Provides a near 1:1 (<0.5 dB insertion loss) 50Ω coaxial measurement port (type-N)
    • Provides a defined, stable, impedance to the Equipment Under Test (EUT)
    • Individual Calibration Included
    • Three Year Warranty
    Request Quote
    Request Quote/More Info
    Add to Compare
  • Quick view
    • Price is for a pair of LI-550A LISN's
    • Fully compliant to CISPR 16-1-2 / CISPR 25
    • "Air-core" inductors to prevent saturation
    • Provides a near 1:1 (<0.5 dB insertion loss) 50Ω coaxial measurement port (type-N)
    • Provides a defined, stable, impedance to the Equipment Under Test (EUT)
    • Individual Calibration Included
    • Three Year Warranty
    Request Quote
    Request Quote/More Info
    Add to Compare
Showing 1 - 12 of 53 items