MIL-STD-461 CS101

MIL-STD-461 CS101 Purpose

Conducted Susceptibility, Power Leads, 30 Hz to 150 kHz

This test procedure is used to verify the ability of the EUT to withstand signals coupled onto input power leads. There are two methods provided for making measurements of the applied signal. The first uses an oscilloscope with a power input isolation transformer. ...

MIL-STD-461 CS101 Purpose

Conducted Susceptibility, Power Leads, 30 Hz to 150 kHz

This test procedure is used to verify the ability of the EUT to withstand signals coupled onto input power leads. There are two methods provided for making measurements of the applied signal. The first uses an oscilloscope with a power input isolation transformer. The second uses a measurement receiver together with a transducer. The transducer is intended to electrically isolate the receiver from the EUT power and reduce the signal levels to protect the receiver.

MIL-STD-461 CS101 Test Equipment

The test equipment shall be as follows:

a. Signal generator

b. Power amplifier

c. Oscilloscope or measurement receiver

d. Coupling transformer

e. Capacitor, 10 μF

f. Isolation transformer

g. Resistor, 0.5 ohm

h. LISNs

i. Transducer for measurement receiver use

Get Application Support, Pricing, Lead Time and More: Contact Form

Example Test Setup

mil_std_461_cs101_2

More

MIL-STD-461 CS101 There are 6 products.

Showing 1 - 6 of 6 items
    • Most compact equipment for ripple noise on ac/dc supplies and magnetic fields
    • Built-in LF signal generator
    • Built-in LF amplifier
    • Built-in LF transformer 2:
    • Built-in frequency-selective voltage and current meter
    • Built-in load resistors
    • Automatic self-calibration
    • Frequency Range: 10 Hz - 250 kHz
    Request Quote/More Info
    • EN 55103-1, 2
    • EN/IEC61000-4-8
    • Automotive
    • MIL-STD 
    • Generation and measurement of magnetic fields from DC up to 250 kHz
    • Field strengths up to 1000 A/m 
    • Additional Options (separate)
      • Sensor coils
      • Helmholtz coils
      • Test adapter
    Request Quote/More Info
    • One-box transformer and 0.5 ohm load assembly
    • Frequency response 10 Hz to 250 kHz
    • Secondary saturation 50 A per transformer
    • Audio power 2 x 200 W
    • Freely configurable on primary/secondary; serial, parallel, single
    • Turns ratio 2:1 step down
    • Built-in non-inductive load resistor 0.5 ohm, 250 W
    Request Quote/More Info
    • The EMC Shop supplies equipment solutions for all your MIL-STD-461 CS101 and RS101 testing requirements
    • Equiment configurations include:
      • Signal generator
      • Power amplifier
      • Oscilloscope
      • LISNs
      • Radiating loop
      • Coupling transformer
      • Field monitoring sensor
      • Current probe
    Request Quote/More Info
    • Multi-purpose Power Amplifier
    • Can be used within the Frequency Range from DC to 250 kHz
    • Typical applications are magnetic immunity testing according to automotive standards or MIL-461F
    • Frequency range (nominal): DC - 250 kHz
    • Gain at 8 ohm impedance: 26 dB ±3 dB
    Request Quote/More Info
    • 5 Hz to 1 MHz
    • Multi-Purpose Power Amplifier
    • Typical applications are magnetic immunity testing;
    • According to automotive standards or MIL-461 E or F
    • Frequency range (nominal): 5 Hz - 1 MHz
    • Gain at 8 ohm impedance: 26 dB ±3 dB
    Request Quote/More Info
Showing 1 - 6 of 6 items