MIL-STD-461

Test equipment for all versions of MIL-STD-461 including Version G released Decemeber 2015.

MIL-STD-461 Emission and Susceptibility Testing Breakdown

Conducted emissions requirements are designated by CE

Radiated emissions requirements are designated by RE

Conducted susceptibility requirements are designated by CS

Radiated susceptibility requirements are designated by RS

Get Application Support, Pricing, Lead Time and More: Contact Form

MIL-STD-461 There are 82 products.

Subcategories

  • Radiated Susceptibility

    MIL-STD-461 Radiated Susceptibility Description:

    The EMC Shop stock a variety of MIL-STD-461 Radiated Susceptibility test equipment for Magnetic Field, Electric Field, and Transient Electromagnetic Field applications.

    Get Application Support, Pricing, Lead Time and More: Contact Form

  • Conducted Susceptibility

    The EMC can provide test eqipment for subcategories of MIL-STD-461; Conducted Susceptibility with applications for:

    Power Leads, Antenna Port, Intermodulation, Rejection of Undesired Signals, Cross-Modulation, Structure Current, Bulk Cable Injection, Impulse Excitation, Damped Sinusoidal Transients, Cables and Power Leads, Lightning Induced Transients, and Personnel Borne Electrostatic Discharge

    Get Application Support, Pricing, Lead Time and More: Contact Form

  • Radiated Emissions

    The EMC Shop stocks and delivers a wide array MIL-STD-461 Radiated Emissions equipment. Applications include: Magnetic Field, Electric Field,Antenna Spurious and Harmonic Outputs.

  • Conducted Emissions

    MIL-STD-461 conducted emission testing equipments for power leads, antenna terminals and more. The EMC Shop carries a variety of testing equipment for all MIL-STD-461 compliance tests.

    The conducted emissions testing for MIL-STD-461 is similar to DO-160 Conducted Emissions testing.

    CE101 Applicability

    MIL-STD-461 CE101 requirement is applicable for power leads, including returns, that obtain power from other sources not part of the EUT.

    For AC applications, this requirement is applicable starting at the second harmonic of the EUT power frequency.

    CE101 Test Procedure

    This test procedure is used to verify that electromagnetic emissions from the EUT do not exceed the specified requirements for power input leads including returns. 5.4.3.2 Test equipment. The test equipment shall be as follows:

    a. Measurement receivers

    b. Current probes

    c. Signal generator

    d. Data recording device

    e. Oscilloscope

    f. Resistor (R)

    g. LISNs

per page
Showing 1 - 12 of 82 items
  • Request Quote/More Info
    • Rentals ship immediately
    • Monthly Rate Price
    • Current ISO 17025 Calibration Provided
    • Meets CISPR 16-1-1: 2010 and MIL-STD-461
    • Frequency Range: 20 Hz - 40 GHz
    • Configuration Includes:
      • B10: External Generator Control via GPIB
      • B18: Removable Hard Disk
    $7,995.00
    In Stock
    Request Quote/More Info
    • Meets RTCA/DO 160 Section 22 Levels 1-5
    • Pre-Programmged Test Procedures
    • Intelligent Mains Controlled by Program, Stable Charging w/ High Effeciency
    • Auto Safety Protection Program
    4-6 Weeks
    Request Quote/More Info
    • In accordance with MIL-STD-461E/F, Method CS116
    • Capable of limited testing for RTCA DO-160D, Section 22
    • Panel-mounted digital voltmeter monitors the adjusted open circuit discharge voltage
    • Pulse rates up to one pulse per second maximum (factory adjusted)
    • Single pulse feature enables controlled isolation of transient effects

    Typically In Stock
    Request Quote/More Info
    • Meets RTCA/DO 160 Section 22 Levels 1-5
    • Meets MIL-STD-461G CS 117 Levels 1-5
    • Pre-Programmed Test Procedures
    • On-site Installation, Debugging and Training
    • Intelligent Mains Controlled by Program, Stable Charging w/ High Efficiency
    • Auto Safety Protection Program
    5-6 Months
    Request Quote/More Info
    • New Purchase Price: $1199.00
    • Price is for a pair of LI-125A line impedance stabilization networks
    • Fully compliant to MIL-STD 461
    • Provides a near 1:1 (<0.5 dB insertion loss) 50Ω coaxial measurement port (type-N)
    • Provides a defined, stable, impedance to the Equipment Under Test (EUT)
    • Individual Calibration Included
    • Three Year Warranty
    $1,199.00
    Typically In Stock
    Request Quote/More Info
    • One-box transformer and 0.5 ohm load assembly
    • Frequency response 10 Hz to 250 kHz
    • Secondary saturation 50 A per transformer
    • Audio power 2 x 200 W
    • Freely configurable on primary/secondary; serial, parallel, single
    • Turns ratio 2:1 step down
    • Built-in non-inductive load resistor 0.5 ohm, 250 W
    4-6 Weeks
    Request Quote/More Info
    • Most compact equipment for ripple noise on ac/dc supplies and magnetic fields
    • Built-in LF signal generator
    • Built-in LF amplifier
    • Built-in LF transformer 2:
    • Built-in frequency-selective voltage and current meter
    • Built-in load resistors
    • Automatic self-calibration
    • Frequency Range: 10 Hz - 250 kHz
    In Stock
    Request Quote/More Info
    • MIL-STD 461 CS116 Compliant
    • 5.7" touch screen
    • 17 waveform variations
    • 10 kHz - 100 MHz
    4-6 Weeks
    Request Quote/More Info
    • 30 Hz to 100 kHz frequency range
    • Radiating Loop and Loop Sensor
    • MIL-STD-461D/RS101 magnetic field tests
    Request Quote/More Info
    • The EMC Shop supplies equipment solutions for all your MIL-STD-461 CS101 and RS101 testing requirements
    • Equiment configurations include:
      • Signal generator
      • Power amplifier
      • Oscilloscope
      • LISNs
      • Radiating loop
      • Coupling transformer
      • Field monitoring sensor
      • Current probe
    4-6 Weeks
    Request Quote/More Info
    • Single generator output for CS114, CS115 and CS116 tests allowing remote test automation
    • Automatic calibration for each test and for the full test frequency range
    • Automatic configuration of the measurement equipment settings
    • Built-in scroll-down menus for selecting test equipment and components
    • Test and calibration reports automatically generated
    4-6 Weeks
    Request Quote/More Info
Showing 1 - 12 of 82 items