MIL-STD-461 CS101


MIL-STD-461 Testing Services         Radiated Immunity & Susceptibility        Antenna Testing            Emissions Testing


Get Application Support, Pricing, Lead Time and More: Contact Form

MIL-STD-461 CS101 Purpose

Conducted Susceptibility, Power Leads, 30 Hz to 150 kHz

This test procedure is used to verify the ability of the EUT to withstand signals coupled onto input power leads. There are two methods provided for making measurements of the applied signal. The first uses an oscilloscope with a power input isolation transformer. The second uses a measurement receiver together with a transducer. The transducer is intended to electrically isolate the receiver from the EUT power and reduce the signal levels to protect the receiver.

MIL-STD-461 CS101 Test Equipment

The test equipment shall be as follows:

a. Signal generator

b. Power amplifier

c. Oscilloscope or measurement receiver

d. Coupling transformer

e. Capacitor, 10 μF

f. Isolation transformer

g. Resistor, 0.5 ohm

h. LISNs

i. Transducer for measurement receiver use


MIL-STD-461 CS101 Test Setup

MIL-STD-461 CS101 Test Setup

MIL-STD-461 CS101 There are 8 products.

Showing 1 - 8 of 8 items
    • Test equipment bundle with software for easy testing
    • Semi-automatic calibration routine significantly reduces labor-intensive tasks for MIL 461 CS101 Testing
    • Ships Same Day
    Request Quote/More Info
    • Most compact equipment for ripple noise on ac/dc supplies and magnetic fields
    • Built-in LF signal generator
    • Built-in LF amplifier
    • Built-in LF transformer 2:
    • Built-in frequency-selective voltage and current meter
    • Built-in load resistors
    • Automatic self-calibration
    • Frequency Range: 10 Hz - 250 kHz
    Request Quote/More Info
    • Magnetic field tests and measurement DC to 250 kHz
    • Complies to all relevant EMC, Automotive and Military Standards
    • Magnetic field strength up to 1000 A/m at 1000 Hz
    • Fully automated tests with triaxial Helmholtz coil
    • Wide choice of accessories
    Request Quote/More Info
    • EN 55103-1, 2
    • EN/IEC61000-4-8
    • Automotive
    • MIL-STD 
    • Generation and measurement of magnetic fields from DC up to 250 kHz
    • Field strengths up to 1000 A/m 
    • Additional Options (separate)
      • Sensor coils
      • Helmholtz coils
      • Test adapter
    Request Quote/More Info
    • One-box transformer and 0.5 ohm load assembly
    • Frequency response 10 Hz to 250 kHz
    • Secondary saturation 50 A per transformer
    • Audio power 2 x 200 W
    • Freely configurable on primary/secondary; serial, parallel, single
    • Turns ratio 2:1 step down
    • Built-in non-inductive load resistor 0.5 ohm, 250 W
    Request Quote/More Info
    • The EMC Shop supplies equipment solutions for all your MIL-STD-461 CS101 and RS101 testing requirements
    • Equiment configurations include:
      • Signal generator
      • Power amplifier
      • Oscilloscope
      • LISNs
      • Radiating loop
      • Coupling transformer
      • Field monitoring sensor
      • Current probe
    Request Quote/More Info
    • Multi-purpose Power Amplifier
    • Can be used within the Frequency Range from DC to 250 kHz
    • Typical applications are magnetic immunity testing according to automotive standards or MIL-461F
    • Frequency range (nominal): DC - 250 kHz
    • Gain at 8 ohm impedance: 26 dB ±3 dB
    Request Quote/More Info
    • 5 Hz to 1 MHz
    • Multi-Purpose Power Amplifier
    • Typical applications are magnetic immunity testing;
    • According to automotive standards or MIL-461 E or F
    • Frequency range (nominal): 5 Hz - 1 MHz
    • Gain at 8 ohm impedance: 26 dB ±3 dB
    Request Quote/More Info
Showing 1 - 8 of 8 items