844.423.7435
Equipment & Materials
-
Transient Generators
- Automotive Transient Immunity Generators
- Military Transient Pulse Generators
- Electrical Fast Transient EFT/Burst Generators
- Combination Wave/Surge Generators
- Multi-Test EMC Generators
- Ring Wave Immunity Generators
- Lightning Surge Generators
- Surge & Burst/EFT Generators
- Magnetic Field Generators
- Telecom Testing Generators
- EMI Receivers/EMC Analyzers
- RF Power Amplifiers
- RF Conducted Immunity
- RF Field Strength Meters
- Electrostatic Discharge (ESD) Guns
- EMC Antennas
- Antenna Preamplifiers
- Line Impedance Stabilization Networks (LISN's)
- EMC/EMI Signal Generators
- RF Power Meters
- Bulk Current Injection (BCI) Probes
- EMC Probes
- Coupling Decoupling Networks (CDN's)
- Power Fail Simulators
- Software for EMC Testing
- Calibration Equipment
-
International (IEC/EN)
- EN/IEC 61000-3-2
- EN/IEC 61000-3-3
- EN/IEC 61000-3-11
- EN/IEC 61000-3-12
- EN/IEC 61000-4-2
- EN/IEC 61000-4-3
- EN/IEC 61000-4-4
- EN/IEC 61000-4-5
- EN/IEC 61000-4-6
- EN/IEC 61000-4-7
- EN/IEC 61000-4-8
- EN/IEC 61000-4-9
- EN/IEC 61000-4-10
- EN/IEC 61000-4-11
- EN/IEC 61000-4-12
- EN/IEC 61000-4-16
- EN/IEC 61000-4-18
- EN/IEC 61000-4-19
- EN/IEC 61000-4-20
- EN/IEC 61000-4-21
- EN/IEC 61000-4-29
- EN/IEC 61000-4-31
- IEC 61000-4-39
- Military & Aerospace Standards
- Automotive EMC Standards
- CISPR Standards
- FCC Part 15
- CE Mark Testing
- ANSI/IEEE Standards
- Standards by Product/Industry
- Telecom Testing
EMC Manufacturers
-
Transient Generators
- Automotive Transient Immunity Generators
- Military Transient Pulse Generators
- Electrical Fast Transient EFT/Burst Generators
- Combination Wave/Surge Generators
- Multi-Test EMC Generators
- Ring Wave Immunity Generators
- Lightning Surge Generators
- Surge & Burst/EFT Generators
- Magnetic Field Generators
- Telecom Testing Generators
- EMI Receivers/EMC Analyzers
- RF Power Amplifiers
- RF Conducted Immunity
- RF Field Strength Meters
- Electrostatic Discharge (ESD) Guns
- EMC Antennas
- Antenna Preamplifiers
- Line Impedance Stabilization Networks (LISN's)
- EMC/EMI Signal Generators
- RF Power Meters
- Bulk Current Injection (BCI) Probes
- EMC Probes
- Coupling Decoupling Networks (CDN's)
- Power Fail Simulators
- Software for EMC Testing
- Calibration Equipment
-
International (IEC/EN)
- EN/IEC 61000-3-2
- EN/IEC 61000-3-3
- EN/IEC 61000-3-11
- EN/IEC 61000-3-12
- EN/IEC 61000-4-2
- EN/IEC 61000-4-3
- EN/IEC 61000-4-4
- EN/IEC 61000-4-5
- EN/IEC 61000-4-6
- EN/IEC 61000-4-7
- EN/IEC 61000-4-8
- EN/IEC 61000-4-9
- EN/IEC 61000-4-10
- EN/IEC 61000-4-11
- EN/IEC 61000-4-12
- EN/IEC 61000-4-16
- EN/IEC 61000-4-18
- EN/IEC 61000-4-19
- EN/IEC 61000-4-20
- EN/IEC 61000-4-21
- EN/IEC 61000-4-29
- EN/IEC 61000-4-31
- IEC 61000-4-39
- Military & Aerospace Standards
- Automotive EMC Standards
- CISPR Standards
- FCC Part 15
- CE Mark Testing
- ANSI/IEEE Standards
- Standards by Product/Industry
- Telecom Testing
Shop by Brand
MIL-STD-461 CE102
Using the measurement system hardware including the LISN, cable, limiter, attenuator, and spectrum analyzer to measure the voltage at the LISN measurement port. The measurement system software should apply the appropriate correction and conversion factors to reduce the data. The resulting measurement should be 6 dB below the limit ±3 dB.
CE 102 Purpose
Conducted emissions, power leads
This requirement is applicable from 10 kHz to 10 MHz for all power leads, including returns, which obtain power from other sources not part of the EUT.
This test procedure is used to verify that electromagnetic emissions from the EUT do not exceed the specified requirements for power input leads, including returns.
Test Equipment
The test equipment shall be as follows:
a. Measurement receiver
b. Data recording device
c. Signal generator
d. Attenuator, 20 dB, 50 ohm
e. Oscilloscope
f. LISNs
Get Application Support, Pricing, Lead Time and More: Contact Form