MIL-STD-461 CS116

CS116 Purpose

Conducted susceptibility, damped sinusoidal transients, cables and power leads.

This requirement is applicable from 10 kHz to 100 MHz for all interconnecting cables, including power cables, and individual high side power leads. Power returns and neutrals need not be tested individually.
This test procedure is used to verify the ...

CS116 Purpose

Conducted susceptibility, damped sinusoidal transients, cables and power leads.

This requirement is applicable from 10 kHz to 100 MHz for all interconnecting cables, including power cables, and individual high side power leads. Power returns and neutrals need not be tested individually.
This test procedure is used to verify the ability of the EUT to withstand damped sinusoidal transients coupled onto EUT associated cables and power leads.

Test Equipment

The test equipment shall be as follows:

a. Damped sinusoid transient generator, ≤ 100 ohm output impedance
b. Current injection probe
c. Oscilloscope, 50 ohm input impedance
d. Calibration fixture: Coaxial transmission line with 50 ohm characteristic impedance, coaxial connections on both ends, and space for an injection probe around the center conductor
e. Current probes
f. Waveform recording device
g. Attenuators, 50 ohm
h. Measurement receivers
i. Coaxial loads, 50 ohm
j. LISNs

Get Application Support, Pricing, Lead Time and More: Contact Form

More

MIL-STD-461 CS116 There are 9 products.

Showing 1 - 9 of 9 items
  • Request Quote/More Info
    • MIL-STD-461 CS114, CS115, CS116
    • Maximum input power 100W for 60 minutes 
    • Case temperature < 50°C 
    • 10 kHz to 400 MHz 

    To Rent Pearson 8700i

    $4,475.00
    Request Quote/More Info
    • Use with probes 8700i and 8705C
    • 10 kHz to 400 MHz 
    • VSWR < 3
    • MIL-STD-461 CS114, CS115, CS116
    $2,450.00
    Request Quote/More Info
    • 10 kHz to 400 MHz Frequency Range
    • Maximum RMS Current 4 A
    • MIL-STD-461 CS114, CS115, CS116
    • Calibration Fixture F-3

    To Rent Pearson 8705C

    $2,850.00
    Request Quote/More Info
    • In accordance with MIL-STD-461E/F, Method CS116
    • Capable of limited testing for RTCA DO-160D, Section 22
    • Panel-mounted digital voltmeter monitors the adjusted open circuit discharge voltage
    • Pulse rates up to one pulse per second maximum (factory adjusted)
    • Single pulse feature enables controlled isolation of transient effects

    Request Quote/More Info
    • Single generator output for CS114, CS115 and CS116 tests allowing remote test automation
    • Automatic calibration for each test and for the full test frequency range
    • Automatic configuration of the measurement equipment settings
    • Built-in scroll-down menus for selecting test equipment and components
    • Test and calibration reports automatically generated
    Request Quote/More Info
    • MIL-STD-461 CS114, CS115, CS116
    • Maximum input power 100W for 60 minutes
    • Case temperature < 50°C
    • 10 kHz to 400 MHz
    • Ratio 1:1
    • Weight 6 lb (2.7 kg
    • Hole Diameter 2.0 inches [50.8 mm]
    • Width 5.75 inches [147 mm]
    • Height 5.0 inches [127 mm]
    • Thickness 1.63 inches [41 mm])
    • Use with calibration fixture F-3

    To Purchase Pearson 8700i

    $395.00
    Request Quote/More Info
    • Frequency Range 10 kHz to 400 MHz
    • Includes:
      • Pearson 8700i Current Injection Probe
      • Pearson 8705 Current Monitor
      • Pearson F-3 Calibration Jig
    • MIL-STD-461 CS114, CS115, CS116
    • DO-160 Section 21, rf CE (8705C)
    • AIAA S-121 Radio Frequency CS
    • NASA GSFC EMI Specs CE03, Bulk current emission
    • Automotive Chrysler Radio Frequency CE
    • John Deere Radio Frequency CE
    • BMW Radio Frequency CE
    • IEC / EN 61000-4-6
    • TR-102323 Radio Frequency CS
    Request Quote/More Info
    • 10 kHz to 400 MHz Frequency Range
    • Maximum RMS Current 4 A
    • MIL-STD-461 CS114, CS115, CS116
    • Calibration Fixture F-3

    To Purchase Pearson 8705C

    Request Quote/More Info
Showing 1 - 9 of 9 items