Military Transient Pulse Generators

Rent, buy or lease military transient pulse generators at The EMC Shop, a company specialized in MIL-STD, DO-160 and other compliance testing.

Military Transient Pulse Generators There are 12 products.

Showing 1 - 12 of 12 items
    • 10 kHz–400 MHz Frequency Range
    • Bulk Current Injection (BCI) RF Conducted Immunity System
    • 100 Watts nominal

    Complete testing solutions to the following standards:

    • MIL-STD-461D & E CS114
    • DO160D & E BCI Testing
    • EN/IEC 61000-4-6
    • IEC 60601-1-2
    • EN 50130-4
    • EN 61000-6-1/2
    • EN 55024
    Request Quote/More Info
    • Most compact equipment for ripple noise on ac/dc supplies and magnetic fields
    • Built-in LF signal generator
    • Built-in LF amplifier
    • Built-in LF transformer 2:
    • Built-in frequency-selective voltage and current meter
    • Built-in load resistors
    • Automatic self-calibration
    • Frequency Range: 10 Hz - 250 kHz
    Request Quote/More Info
    • Monthly Rental - Ships Immediately
    • CDN, BCI Probe or EM Clamp Required to complete test setup
    • Meet RF & Conducted Immunity Compliance Standards:
      • EN/IEC 61000-4-6
      • MIL-STD461 CS114
      • RTCA/DO160 Section 20
      • ISO 11452 part 4 BCI
      • ISO 11452 part 5 Stripline
      • IEC 60601-1-2
      • EN 61000-6-1/EN 61000-6-2
      • Various Automotive Manufacturer's Specifications
    Request Quote/More Info
    • Meets RTCA/DO 160 Section 22 Levels 1-5
    • Meets MIL-STD-461G CS 117 Levels 1-5
    • Pre-Programmed Test Procedures
    • On-site Installation, Debugging and Training
    • Intelligent Mains Controlled by Program, Stable Charging w/ High Efficiency
    • Auto Safety Protection Program
    Request Quote/More Info
    • Single generator output for CS114, CS115 and CS116 tests allowing remote test automation
    • Automatic calibration for each test and for the full test frequency range
    • Automatic configuration of the measurement equipment settings
    • Built-in scroll-down menus for selecting test equipment and components
    • Test and calibration reports automatically generated
    Request Quote/More Info
    • Provides output levels from 10 V to more than 400 V into 5 Ω
    • Adjustable pulse position on AC lines relates the transient susceptibility to real
    • time aspects of digital systems
    • Single pulse feature for controlled isolation of transient effects
    • Output terminals for series and parallel injection
    • Standard rack panel construction: 19" wide x 7" high x 12.75" deep
    Request Quote/More Info
    • Provides outputs up to 600 volts peak amplitude for the 0.15, 5.0 and 10.0 S spikes into a five ohm resistive load (low source impedance).
    • A wide range of repetition rates allows spike injection in terms of the pulse rates of items being tested.
    • The single pulse feature enables controlled isolation of transient effects.
    • Adjustable pulse position on a.c. power lines relates the transient susceptibility to the real time aspects of digital circuitry served by a.c. power.
    • Transients can be injected in synchronism with repetitive circuit functions as required by Method CS06 of MIL-STD-462.
    • Remote triggering of single or repetitive pulses in terms of particular system characteristics.

    To Rent Solar 8282-1

    Request Quote/More Info
    • In accordance with MIL-STD-461E/F, Method CS116
    • Capable of limited testing for RTCA DO-160D, Section 22
    • Panel-mounted digital voltmeter monitors the adjusted open circuit discharge voltage
    • Pulse rates up to one pulse per second maximum (factory adjusted)
    • Single pulse feature enables controlled isolation of transient effects

    Request Quote/More Info
  • Request Quote/More Info
  • Request Quote/More Info
    • Provides output levels from 10 V to 600 V into 5 Ω. Delivers more than 300 kW peak into 0.5 Ω load
    • Adjustable pulse position on AC lines relates the transient susceptibility to real time aspects of digital systems
    • Single pulse feature for controlled isolation of transient effects
    • Output terminals for series or parallel injection
    • Includes 2201-1 and 2201-2 transformers
    • Standard rack panel construction: 19" wide x 7" high x 12.75" deep (48.26 cm x 17.78 cm x 32.38 cm)
    Request Quote/More Info
    • Panel-mounted digital meters monitor the adjustable charged line voltage and pulse repetition rate.
    • Adjustable pulse rate from 0.6 p.p.s. to 150 p.p.s., and manual triggering via front panel push button.
    • Charged line output voltage adjustable from 1.0 V to >2000 V
    • Pulse generator with spectral output calibrated in terms of dB V/MHz into a 50 ohms load
    Request Quote/More Info
Showing 1 - 12 of 12 items