Solar Electronics

Solar Electronics is a USA based manufacturer of military and aerospace EMI and EMC test equipment for product compliance to test standards such as MIL-STD-461 and RTCA/DO-160. The EMC Shop stocks Solar EMI/EMC test equipment to support immediate testing needs.

Solar Electronics There are 18 products.

per page
Showing 1 - 12 of 18 items
    • Compliant to FCC Part 15, CISPR 16-1, ANSI C63.4 (1992)
    • Rentals Ship Immediately
    • Price is Monthly Rental Rate
    • 50 Amp Capability per line
    Request Quote/More Info
  • Provides a convenient bench model unit with three-way binding posts on primary and output voltmeter leads. Standard 0.75" spacing of binding posts allows use of standard plugs. High current secondary uses 1/4-20 threaded studs.

    Request Quote/More Info
    • Compliant to FCC Part 15, CISPR 16-1, ANSI C63.4 (1992)
    • 50 Amp Capability per line
    Request Quote/More Info
    • for Test Method RE101 of MIL-STD-461F
    • Required by Test Method RE01 in Parts 2 through 6 of MIL-STD- 461C and
    • RE101 of MIL-STD-461D/E/F
    Request Quote/More Info
    • RS01 magnetic field tests
    • described in Figure 1A of MIL-STD-461A
    • ten turns of number 16 AWG
    • 4.72" (12 cm) in diameter
    Request Quote/More Info
    • 30 Hz to 100 kHz frequency range
    • Radiating Loop and Loop Sensor
    • MIL-STD-461D/RS101 magnetic field tests
    Request Quote/More Info
    • High insulation resistance over a wide temperature range
    • Excellent stability with long life
    • Built-in discharge resistor for safety
    • Designed for bulkhead or bench mounting
    Request Quote/More Info
    • Modular design 
    • Single rack portability 
    • Programmable single stroke, multiple stroke, multiple burst waveforms 
    • Pin injection, cable bundle injection, ground injection up to Level 3 
    • Self-contained microprocessor control 
    • LCD system display
    • lightning induced transient susceptibility testing
    • requirements of RTCA/DO-160E/F/G Section 22 are met at Levels 1 through 3
    Request Quote/More Info
    • Provides output levels from 10 V to more than 400 V into 5 Ω
    • Adjustable pulse position on AC lines relates the transient susceptibility to real
    • time aspects of digital systems
    • Single pulse feature for controlled isolation of transient effects
    • Output terminals for series and parallel injection
    • Standard rack panel construction: 19" wide x 7" high x 12.75" deep
    Request Quote/More Info
    • Provides outputs up to 600 volts peak amplitude for the 0.15, 5.0 and 10.0 S spikes into a five ohm resistive load (low source impedance).
    • A wide range of repetition rates allows spike injection in terms of the pulse rates of items being tested.
    • The single pulse feature enables controlled isolation of transient effects.
    • Adjustable pulse position on a.c. power lines relates the transient susceptibility to the real time aspects of digital circuitry served by a.c. power.
    • Transients can be injected in synchronism with repetitive circuit functions as required by Method CS06 of MIL-STD-462.
    • Remote triggering of single or repetitive pulses in terms of particular system characteristics.

    To Rent Solar 8282-1

    Request Quote/More Info
    • In accordance with MIL-STD-461E/F, Method CS116
    • Capable of limited testing for RTCA DO-160D, Section 22
    • Panel-mounted digital voltmeter monitors the adjusted open circuit discharge voltage
    • Pulse rates up to one pulse per second maximum (factory adjusted)
    • Single pulse feature enables controlled isolation of transient effects

    Request Quote/More Info
    • Frequency range: 10 kHz to 500 MHz
    • Transfer impedance (ZT): 1.0 to 5.0 Ω above 300 kHz
    • Output load impedance: 50 + j 0 Ω
    • Continuous signal current (CW): 40 A
    • Maximum power current: 200 A DC to 400 Hz
    Request Quote/More Info
Showing 1 - 12 of 18 items